Charged ReviewsSaved 0Compare 0Login

Charged Reviews

Quick reference

OutBack Power FLEXmax 80 Solar Charge Controller

Model: FLEXmax 80 · SKU: FM80-150VDC

Prepared

Common specifications

FieldValueSources
Controller typeMPPT[1] [2]
Max PV voltage150 VDC[1] [2]
Max PV input power4000 W[2]
Max PV input power12: 1,000, 24: 2,000, 48: 4,000, 60: 5,000 W[2]
Max PV current?
Charge current80 A[1] [2]
Battery voltage12, 24, 36, 48, or 60VDC[2]
Supported chemistry?
Efficiency?
MPPT tracking efficiency?
Max conversion efficiency98.44 %[2]
Full load efficiency?
Charger efficiency?
Weighted efficiency97.3 %[2]
Rated charge power?
Load output?
Self consumption ma?
Enclosure ratingIndoor Type 1[2]
ListingUL 1741 2nd Edition, CSA C22.2 No. 107.1-01, IEC 62509:2010[1]
Enclosure volume6.12 L Calculated[1]
Warranty term5 years[2]

All recorded specifications

FieldValueSources
ListingUL 1741 2nd Edition, CSA C22.2 No. 107.1-01, IEC 62509:2010[1]
GroundingThis product is intended to be installed as part of a permanently grounded electrical system; The negative battery conductor should be bonded to the grounding system at only one point in the system.; The FLEXmax controller is not intended to be wired into a positive-ground configuration.[1]
Weight5.53 kg[2]
PV wire sizeUp to #2 AWG (33.6 mm2); input conductors rated at 1.56 times the PV array short-circuit current (NEC)[1]
DimensionsW 146 × H 412.8 × D 101.6 mm / W 5.75 × H 16.25 × D 4 in Needs confirmation[1]
PV disconnectInstall OutBack PNL-80-DC circuit breakers for disconnect and overcurrent protection; Input conductors and circuit breakers must be rated at 1.56 times the short-circuit current of the PV array (according to NEC).[1]
CommunicationsProprietary network system using RJ-45 modular connectors with CAT5 cable (8 wires)[2]
Controller typeMPPT[1] [2]
Charge current80 A[1] [2]
Enclosure ratingIndoor Type 1[2]
Ground wire sizeUp to 35 mm2 (#2 AWG)[1]
Max PV voltage150 VDC[1] [2]
Battery voltage12, 24, 36, 48, or 60VDC[2]
Battery wire sizeMinimum #4 AWG (25 mm2) between the FLEXmax 80 and the battery bus bar; up to #2 AWG (33.6 mm2)[1]
Battery protectionDC battery overcurrent protection must be used as part of the installation.; Install OutBack PNL-80-DC circuit breakers for disconnect and overcurrent protection[1]
Max PV input power4000 W[2]
PV terminal torque4 N·m[1]
Communication portsMATE/HUB RJ45 port; Battery Remote Temp Sensor (RTS) RJ11 port[1]
Max PV input power12: 1,000, 24: 2,000, 48: 4,000, 60: 5,000 W[2]
Mounting orientationUpright position out of direct sunlight[1]
Ground terminal torque4 N·m[1]
Battery terminal torque4 N·m[1]
Operating temperature–40 to 60°C[2]
Weighted efficiency97.3 %[2]
Max conversion efficiency98.44 %[2]

Warranty

FieldValueSources
Warranty term5 years[2]

Certificate records

StandardRecordEvidenceSources
UL 1741Claimed · present at observation[2]
CSA C22.2 No. 107.1Claimed · present at observation[2]

Sources and revisions

  1. OutBack Power FLEXmax Series Charge Controllers (FLEXmax 80) Owner's Manual (900-0009-01-00 Rev D) Installation manual · Revision Rev D · Revised 2020-01 · Checked Oct 1, 2026 https://outbackpower.com/wp-content/uploads/2026/06/owner_manual.pdf
  2. OutBack Power's own FLEXmax 80 Specifications datasheet, dated 2026, linked from OutBack Power's own outbackpower.com FLEXmax 60/80 product page. Manufacturer datasheet (PDF) · Checked Sep 27, 2026 https://outbackpower.com/wp-content/uploads/2026/06/fm80-datasheet-2026.pdf