Charged ReviewsSaved 0Compare 0Login
OutBack Power
Charge controller

OutBack Power FLEXmax 100 AFCI Solar Charge Controller

Key specs

Charge current100 A
Weight7.3 kg
Max PV voltage300 VDC
Max conversion efficiency98.8 %
Max PV current64 A
OutBack Power FLEXmax 100 AFCI Solar Charge Controllerread Nov 14, 2026

All specifications

Identity

BrandOutBack Power · Website
ModelFLEXmax 100 AFCI
MarketUnknown
Manufacturer SKUFM100-300VDC-AFCI
About brandOutBack Power's About page says the company has made battery-based power equipment since 2001, including off-grid inverter/chargers, grid-interactive inverter systems, MPPT charge controllers and energy storage. It says OutBack Power is now part of Energy Access Innovations (EAI). Its datasheets name OutBack Power Technologies, Inc. of Phoenix, Arizona.
SKU detail
locator: Model line
conditions: Printed as the datasheet's own model designation; Greentech Renewables' own listing carries the same designation as its part number.
Sources: [1]
FieldValueConditionsSource
ListingUL1741; CSA C22.2 No. 107.1-16; IEC 62109-1:2010
Printed as "This product carries a listing report by ETL. It is listed to the following standards:" in OutBack Power's FLEXmax 100 Charge Controller FM100-300VDC-01 FM100-300VDC-AFCI Owner's Manual (900-0253-01-00 Rev C, June 2022), followed by UL1741 (Ed: 2) and CSA C22.2 No. 107.1-16 (Ed:4); PDF page 68 prints "This product is certified to the following standards:" followed by IEC 62109-1:2010. Manufacturer claim as printed.
Where: PDF page 67, Regulatory Specifications, Listings; PDF page 68, Certifications
[2]
GroundingThis product is intended to be installed as part of a permanently grounded electrical system.; The product comes with a functional bond established from negative to ground.; The battery conductor (positive or negative) must be bonded to the grounding system at only one point.; Make certain to connect the FLEXmax grounding terminal bus bar to earth ground.
Printed as "The product comes with a functional bond established from negative to ground." in the Grounding section of OutBack Power's FLEXmax 100 Charge Controller FM100-300VDC-01 FM100-300VDC-AFCI Owner's Manual (900-0253-01-00 Rev C, June 2022), with the other quoted sentences; the controller includes internal ground-fault protection, and PDF page 19 sets out the steps for a positive-ground system (remove the bonding jumper, external positive-to-ground bond, external GFDI).
Where: PDF page 18, Wiring, Grounding; PDF page 19, Positive-Ground Systems
[2]
Weight7.3 kg
Printed as this model's own unit weight, excluding shipping packaging.
Where: Model block, Weight row
[1]
PV wire sizeInput conductors rated at 1.56 times the PV array short-circuit current (NEC)
Printed as "Input conductors and circuit breakers must be rated at 1.56 times the short-circuit current of the PV array (per NEC)." in OutBack Power's FLEXmax 100 Charge Controller FM100-300VDC-01 FM100-300VDC-AFCI Owner's Manual (900-0253-01-00 Rev C, June 2022), which refers to the NEC and other codes for PV array cable sizing. No fixed PV conductor size is printed.
Where: PDF page 21, Wiring Size and Requirements
[2]
ClearancesAbove the ground or floor surface: 36” (91.4 cm) Above and below the controller: 6“ (15.2 cm) Right and left sides: 1” (2.5 cm)
Printed as "Clearance requirements (minimum) Above the ground or floor surface: 36” (91.4 cm) Above and below the controller: 6“ (15.2 cm) Right and left sides: 1” (2.5 cm)" in OutBack Power's FLEXmax 100 Charge Controller FM100-300VDC-01 FM100-300VDC-AFCI Owner's Manual (900-0253-01-00 Rev C, June 2022), which adds "This includes clearance for multiple controllers installed next to each other."
Where: PDF page 15, Dimensions and Clearances, Clearance requirements (minimum)
[2]
DimensionsW 224 × H 584 × D 152 mm / W 8.8 × H 23 × D 6 in
Printed as this model's own unit dimensions, excluding shipping packaging; the datasheet notes the height figure includes the cooling fan. Printed as "Dimensions H × W × D (in/cm)*: Unit: 23 × 8.8 × 6 / 58.4 × 22.4 × 15.2" in OutBack Power's FLEXmax 100 AFCI datasheet. Revised on 13 October 2026: stored as text before; converted to numbers using the axis order the document prints (height x width x depth).
Where: Model block, Dimensions row
Sources
Converted: 58.4 x 22.4 x 15.2 cm x 10 mm/cm
[1]
PV disconnectInput conductors and circuit breakers must be rated at 1.56 times the short-circuit current of the PV array (per NEC).; PNL-40-300VDC 40 amp single pole; PNL-40D-300VDC 40 amp double pole; PNL-60-300VDC 60 amp single pole; PNL-60D-300VDC 60 amp double pole; PNL-80-300VDC 80 amp single pole; PNL-80D-300VDC 80 amp double pole
Printed as "The input (PV) and output protective devices must be sized according to the installation requirements." in OutBack Power's FLEXmax 100 Charge Controller FM100-300VDC-01 FM100-300VDC-AFCI Owner's Manual (900-0253-01-00 Rev C, June 2022), followed by the quoted Input Circuit Breakers list. PDF page 19 adds that a positive-ground system needs a dual-pole PV input circuit breaker.
Where: PDF page 21, Circuit Breaker Size and Requirements, Input Circuit Breakers
[2]
CommunicationsProprietary network system using RJ-45 modular connectors
Printed as this model's own network cabling description.
Where: Model block, Network Cabling row
[1]
Controller typeMPPT
Printed as "maximum power point tracking charge controllers" in OutBack Power's FLEXmax 100 Charge Controller FM100-300VDC-01 FM100-300VDC-AFCI Owner's Manual (900-0253-01-00 Rev C, June 2022), whose cover names this model as a charge controller. Re-cited on 1 October 2026 to the manufacturer's own document; previously cited to OutBack Power (outbackpower.com), which stays listed as an additional source.
Where: PDF page 2, About OutBack Power; PDF page 1, cover
[2] [1]
Charge current100 A
Printed as "Maximum Continuous Output Current 100 Adc" in OutBack Power's FLEXmax 100 Charge Controller FM100-300VDC-01 FM100-300VDC-AFCI Owner's Manual (900-0253-01-00 Rev C, June 2022). Re-cited on 1 October 2026 to the manufacturer's own document; previously cited to OutBack Power (outbackpower.com), which stays listed as an additional source.
Where: PDF page 67, Table 10 Electrical and Mechanical Specifications, Maximum Continuous Output Current row
[2] [1]
Enclosure ratingIP54
Printed as "Ingress Protection Rating IP54" in OutBack Power's FLEXmax 100 Charge Controller FM100-300VDC-01 FM100-300VDC-AFCI Owner's Manual (900-0253-01-00 Rev C, June 2022); the same table also prints "Enclosure Type Type 3R". Re-cited on 1 October 2026 to the manufacturer's own document; previously cited to OutBack Power (outbackpower.com), which stays listed as an additional source.
Where: PDF page 67, Table 11 Environmental / Safety Specifications, Ingress Protection Rating row
[2] [1]
Ground wire sizeUp to #6 AWG (16 mm2), 90°C copper
Printed as "The maximum permitted conductor size for connection to the grounding wire terminal block is #6 AWG (16 mm2)." in OutBack Power's FLEXmax 100 Charge Controller FM100-300VDC-01 FM100-300VDC-AFCI Owner's Manual (900-0253-01-00 Rev C, June 2022), followed by "Use 90°C copper wire."
Where: PDF page 21, Wiring Size and Requirements
[2]
Max PV current64 A
Printed as "Maximum Input Current (short-circuit) 64 Adc" in Table 10 of OutBack Power's FLEXmax 100 Charge Controller FM100-300VDC-01 FM100-300VDC-AFCI Owner's Manual (900-0253-01-00 Rev C, June 2022); the figure is printed as a short-circuit input current, and PDF page 21 adds that the largest PV array must have a rated short-circuit current of 64 amps or less under STC.
Where: PDF page 67, Table 10 Electrical and Mechanical Specifications, Maximum Input Current (short-circuit) row
[2]
Max PV voltage300 VDC
Printed as "PV Open-Circuit Voltage 300 Vdc (highest open-circuit voltage before equipment damage)" in OutBack Power's FLEXmax 100 Charge Controller FM100-300VDC-01 FM100-300VDC-AFCI Owner's Manual (900-0253-01-00 Rev C, June 2022); the operating maximum is printed separately as 290 Vdc temperature corrected Voc. Re-cited on 1 October 2026 to the manufacturer's own document; previously cited to OutBack Power (outbackpower.com), which stays listed as an additional source.
Where: PDF page 67, Table 10, PV Open-Circuit Voltage row
[2] [1]
Battery voltage24VDC / 36VDC / 48VDC
Printed as this model's own nominal battery system voltage row.
Where: Model block, Nominal Battery System Voltage row
[1]
Battery wire size#4 AWG (25 mm2) minimum; accepts up to #2 AWG (35 mm2); 90°C copper
Printed as "Use #4 AWG (25 mm2) wire (minimum) for the output between the FLEXmax 100 and the battery bus bar conductors." in OutBack Power's FLEXmax 100 Charge Controller FM100-300VDC-01 FM100-300VDC-AFCI Owner's Manual (900-0253-01-00 Rev C, June 2022), with "The output can accept conductors up to #2 AWG (35 mm2)." and "Use 90°C copper wire."
Where: PDF page 21, Wiring Size and Requirements
[2]
Battery protectionDC battery overcurrent protection must be used as part of the installation.; PNL-100-300VDC 100 amp single pole with plastic shield; PNL-125-300VDC 125 amp single pole with plastic shield; The minimum AIC (amps interrupting capacity) rating required is 1125 Adc.
Printed as "DC battery overcurrent protection must be used as part of the installation." in OutBack Power's FLEXmax 100 Charge Controller FM100-300VDC-01 FM100-300VDC-AFCI Owner's Manual (900-0253-01-00 Rev C, June 2022), which lists OutBack's output circuit breakers as the quoted PNL-100-300VDC and PNL-125-300VDC models and prints the minimum AIC rating.
Where: PDF page 21, Wiring Size and Requirements; Circuit Breaker Size and Requirements, Output Circuit Breakers
[2]
Max PV input power7000 W
Printed as "24 V 3500 W 36 V 5250 W 48 V 7000 W" in Table 13 (Maximum Array Size, Standard Test Conditions) of OutBack Power's FLEXmax 100 Charge Controller FM100-300VDC-01 FM100-300VDC-AFCI Owner's Manual (900-0253-01-00 Rev C, June 2022); the recorded 7000 W is the 48 V row. Re-cited on 1 October 2026 to the manufacturer's own document; previously cited to OutBack Power (outbackpower.com), which stays listed as an additional source.
Where: PDF page 73, Table 13 Maximum Input Wattage Per Charge Controller, 48 V row
Sources
3500 W W

Printed as this model's own maximum array rating at 24V nominal battery voltage.

[1]
5250 W W

Printed as this model's own maximum array rating at 36V nominal battery voltage.

[1]
[2] [1]
PV terminal torque4 N·m
Printed as "All wire lugs and ground terminals are to be tightened to a torque value of 4 Nm (35 in-lb)." in OutBack Power's FLEXmax 100 Charge Controller FM100-300VDC-01 FM100-300VDC-AFCI Owner's Manual (900-0253-01-00 Rev C, June 2022); one figure for all wire lugs and ground terminals, recorded on the PV, battery and ground terminal keys. Printed in two units, newton meters first ("4 Nm", then "35 in-lb").
Where: PDF page 22, Physical Requirements and Conduit
[2]
Communication portsHUB Port (RJ-45); Remote Temperature Sensor Port; Device and LAN Ports (not currently active)
Printed as "HUB Port This is an RJ-45 port for a CAT5-style cable to connect OutBack Power system displays or the HUB communications manager." in OutBack Power's FLEXmax 100 Charge Controller FM100-300VDC-01 FM100-300VDC-AFCI Owner's Manual (900-0253-01-00 Rev C, June 2022), which also names the Remote Temperature Sensor Port and prints "Device and LAN Ports These ports are not currently active."; a MicroSD card slot and an accessory terminal block are also shown.
Where: PDF page 23, Accessory Terminals and Ports
[2]
Max PV input power24: 3,500, 36: 5,250, 48: 7,000 W
Printed as "Nominal Battery Voltage Maximum Array Size (Standard Test Conditions) 24 V 3500 W 36 V 5250 W 48 V 7000 W" in Table 13 of OutBack Power's FLEXmax 100 Owner's Manual (900-0253-01-00 Rev C); the data sheet prints "Maximum Array (STC Nameplate): 3500W / 5250W / 7000W (charging output limited to 100A at battery voltage)".
Where: PDF page 73, Table 13 Maximum Input Wattage Per Charge Controller
[2] [1]
Mounting orientationUpright on a wall or similar flat upright mounting surface; no other mounting positions are allowed
Printed as "The FLEXmax 100 must be mounted upright on a wall or similar flat upright mounting surface. No other mounting positions are allowed." in OutBack Power's FLEXmax 100 Charge Controller FM100-300VDC-01 FM100-300VDC-AFCI Owner's Manual (900-0253-01-00 Rev C, June 2022), which adds "Installation in shade is recommended."
Where: PDF page 16, Mounting the Charge Controller
[2]
Ground terminal torque4 N·m
Printed as "All wire lugs and ground terminals are to be tightened to a torque value of 4 Nm (35 in-lb)." in OutBack Power's FLEXmax 100 Charge Controller FM100-300VDC-01 FM100-300VDC-AFCI Owner's Manual (900-0253-01-00 Rev C, June 2022); one figure for all wire lugs and ground terminals, recorded on the PV, battery and ground terminal keys. Printed in two units, newton meters first ("4 Nm", then "35 in-lb").
Where: PDF page 22, Physical Requirements and Conduit
[2]
Battery terminal torque4 N·m
Printed as "All wire lugs and ground terminals are to be tightened to a torque value of 4 Nm (35 in-lb)." in OutBack Power's FLEXmax 100 Charge Controller FM100-300VDC-01 FM100-300VDC-AFCI Owner's Manual (900-0253-01-00 Rev C, June 2022); one figure for all wire lugs and ground terminals, recorded on the PV, battery and ground terminal keys. Printed in two units, newton meters first ("4 Nm", then "35 in-lb").
Where: PDF page 22, Physical Requirements and Conduit
[2]
Operating temperature–25° to 60°C
Printed as this model's own ambient operating temperature range, with output power reduced above 25°C.
Where: Model block, Operating Temperature Range row
[1]
Weighted efficiency97.3 %
Printed as this model's own CEC weighted efficiency at 48V.
Where: Model block, CEC Weighted Efficiency row
[1]
Max conversion efficiency98.8 %
Printed as "Peak Efficiency: 24V: 97.5% 48V: 98.8%" in OutBack Power's FLEXmax 100 AFCI data sheet; 98.8% is the 48V figure, the higher of the two, and the 24V figure is kept as an alternative. The same block prints "Power Conversion Efficiency: 24V: 96% 48V: 97%". Revised on 13 October 2026: the value was 97, the power conversion efficiency at 48V; it is now the printed peak efficiency at 48V, 98.8.
Where: Model block, Peak Efficiency row, 48V
Sources
97.5 %

Printed as this model's peak efficiency at 24V nominal battery voltage.

[1]
[1]

Owner reviews

No owner reviews yet
Write a review

Sellers

Lowest first. Each price is the date we last read it; it may have changed. Stock isn't shown.

StorePriceReadDetailsSource
Signature Solar$1,894Nov 14, 2026
Discounts and evidence

Discounts

Free shippingQualifying orders of $4,000+
Last checked Sep 23, 2026
Signature Solar · Retail buyers in the lower 48 states
View offer Paid link
Terms
  • Must spend $4,000 or more (the threshold was $3,000 on September 6, 2026).
  • Excludes out-of-stock items, terminal delivery, solar panels/pallets, large module solar panels, Chiko Carports and Chiko Ground Mounts.
  • Installer, wholesale and B2B customer groups are excluded.
  • Limited-time promotion; end date not published. Order contents and delivery route must qualify.

Checked Sep 23, 2026 · End date not published.

Signature Solar promotion terms Paid link

Evidence

One new unit at the listed price; shipping and tax are not included. · Store SKU 1600009
Price readings (14)
  • Oct 4, 2026: $1,894
  • Oct 24, 2026: $1,894
  • Oct 27, 2026: $1,894
  • Oct 28, 2026: $1,894
  • Oct 29, 2026: $1,894
  • Oct 30, 2026: $1,894
  • Oct 31, 2026: $1,894
  • Nov 1, 2026: $1,894
  • Nov 2, 2026: $1,894
  • Nov 3, 2026: $1,894
  • Nov 5, 2026: $1,894
  • Nov 7, 2026: $1,894
  • Nov 11, 2026: $1,894
  • Nov 14, 2026: $1,894
[3] [4]View now Paid link

Price history

Prices we read at Signature Solar · 15 readings · no change in our readings since

Chart, listings & data

Since · Listing price (USD)

View listing at Signature Solar Paid link
$1,700$1,800$1,900$2,000Signature Solar: $1,894 · Oct 4, 2026, 9:20 AM PDTSignature Solar: $1,894 · Oct 24, 2026, 3:04 AM PDTSignature Solar: $1,894 · Oct 27, 2026, 2:54 AM PDTSignature Solar: $1,894 · Oct 28, 2026, 3:24 AM PDTSignature Solar: $1,894 · Oct 29, 2026, 3:47 AM PDTSignature Solar: $1,894 · Oct 30, 2026, 3:52 AM PDTSignature Solar: $1,894 · Oct 31, 2026, 3:35 AM PDTSignature Solar: $1,894 · Nov 1, 2026, 3:47 AM PSTSignature Solar: $1,894 · Nov 2, 2026, 4:11 AM PSTSignature Solar: $1,894 · Nov 3, 2026, 4:24 AM PSTSignature Solar: $1,894 · Nov 5, 2026, 2:13 AM PSTSignature Solar: $1,894 · Nov 7, 2026, 4:20 AM PSTSignature Solar: $1,894 · Nov 11, 2026, 3:21 AM PSTSignature Solar: $1,894 · Nov 14, 2026, 4:53 AM PSTOct 4, 2026Nov 14, 2026
Signature Solar$1,894Nov 14, 2026, 4:53 AM PSTLatest check · hover or tap for earlier prices

A break in a line is a gap in our readings: no price is drawn for days we did not read.

Price data
Collected price observations by seller
CheckedSellerPrice
Oct 4, 2026, 9:20 AM PDTSignature Solar Paid link$1,894
Oct 24, 2026, 3:04 AM PDTSignature Solar Paid link$1,894
Oct 27, 2026, 2:54 AM PDTSignature Solar Paid link$1,894
Oct 28, 2026, 3:24 AM PDTSignature Solar Paid link$1,894
Oct 29, 2026, 3:47 AM PDTSignature Solar Paid link$1,894
Oct 30, 2026, 3:52 AM PDTSignature Solar Paid link$1,894
Oct 31, 2026, 3:35 AM PDTSignature Solar Paid link$1,894
Nov 1, 2026, 3:47 AM PSTSignature Solar Paid link$1,894
Nov 2, 2026, 4:11 AM PSTSignature Solar Paid link$1,894
Nov 2, 2026, 9:26 AM PSTSignature Solar Paid link$1,894
Nov 3, 2026, 4:24 AM PSTSignature Solar Paid link$1,894
Nov 5, 2026, 2:13 AM PSTSignature Solar Paid link$1,894
Nov 7, 2026, 4:20 AM PSTSignature Solar Paid link$1,894
Nov 11, 2026, 3:21 AM PSTSignature Solar Paid link$1,894
Nov 14, 2026, 4:53 AM PSTSignature Solar Paid link$1,894

Quick reference sheet

Controller type
MPPT
Maximum PV voltage (Voc)
300 VDC
Rated charge current
100 A
Battery voltages
24VDC / 36VDC / 48VDC
Maximum PV input power
7000 W
Peak efficiency
Not stated

Evidence score

This category has no Evidence score.

Certificates

What this shows: what each record says and how far it reaches. It does not mean the product is approved.
UL 1741manufacturer claimpresent at observation[1]
Scope
equipment listing
Covered models
FLEXmax 100 AFCI
Limitations
Printed in the manufacturer's own datasheet Certifications row, captured September 28, 2026; no certificate number or issuer file number is given, so it is a manufacturer claim and not issuer-verified.
Record detail
Issued: Not stated
Valid from: Not stated
Expiry: Not stated
Not checked
Source
[1]
CSA C22.2 No. 107.1manufacturer claimpresent at observation[1]
Scope
equipment listing
Covered models
FLEXmax 100 AFCI
Limitations
Printed in the manufacturer's own datasheet Certifications row, captured September 28, 2026; no certificate number or issuer file number is given, so it is a manufacturer claim and not issuer-verified.
Record detail
Issued: Not stated
Valid from: Not stated
Expiry: Not stated
Not checked
Source
[1]
IEC 62109-1manufacturer claimpresent at observation[1]
Scope
equipment listing
Covered models
FLEXmax 100 AFCI
Limitations
Printed in the manufacturer's own datasheet Certifications row, captured September 28, 2026; no certificate number or issuer file number is given, so it is a manufacturer claim and not issuer-verified.
Record detail
Issued: Not stated
Valid from: Not stated
Expiry: Not stated
Not checked
Source
[1]

Warranty

FieldValueConditionsSource
Warranty term5 years
Printed both as a feature bullet and in the specification block.
Where: Feature bullets and Model block, Warranty row
[1]

Recalls / legal notices

No recalls on file. All notices · Report a notice

This register is incomplete. A missing notice does not establish that a product has no recalls.

Documents

Archive and older revisions

Archive and older revisions0

Earlier revisions, archived captures and copies published by someone other than the manufacturer. Every one stays reachable.

Archived documents

OutBack Power's own FLEXmax 100 AFCI Specifications datasheet, document 980-00078-01-001 REV C, dated October 2021, linked from OutBack Power's own outbackpower.com FLEXmax 100 AFCI product page.

Archived copy of a document published by OutBack Power. Copyright retained by the publisher; kept for reference and verification only, no endorsement implied. To ask for its removal, email [email protected].

Archived backupRevision not recorded · 0.46 MB

Archived copy, unaltered, kept as a record of what OutBack Power published. Original address: https://outbackpower.com/downloads/documents/charge_controllers/flexmax_100_afci/flexmax100afci_datasheet.pdf. Copyright and takedown

Source first found
This copy captured
Archived
File detailsOriginal source
Embedded creation date
Embedded modification date
Pages
2

Embedded dates are file metadata, not independent proof of publication.

SHA-256: 7e84f994765d2ea76e161f25e0ea6b5f7730d8ffb22e614dc2ff89194db73350

OutBack Power FLEXmax 100 Charge Controller FM100-300VDC-01 FM100-300VDC-AFCI Owner's Manual (900-0253-01-00 Rev C)

Archived copy of a document published by OutBack Power. Copyright retained by the publisher; kept for reference and verification only, no endorsement implied. To ask for its removal, email [email protected].

Archived backup900-0253-01-00 Rev C · 9.64 MB

Archived copy, unaltered, kept as a record of what OutBack Power published. Original address: https://old.outbackpower.com/downloads/documents/charge_controllers/flexmax_100_afci/fm100_afci_manual.pdf. Copyright and takedown

Source first found
This copy captured
Archived
File detailsOriginal source
Embedded creation date
Embedded modification date
Pages
84

Embedded dates are file metadata, not independent proof of publication.

SHA-256: 5638fdcd10bd758b7a5e1ee8f6c4299dcb45bdf32006ba43080cc9dd9dea9fd1

Submit a document

Parts and accessories

No sourced accessories or replacement parts listed yet.

Model history

Model identity

Model
FLEXmax 100 AFCI

Manufacturer SKU FM100-300VDC-AFCI

No historical observations recorded yet.

Other recorded fields

FieldValueConditionsSource
Evidence breakdownUnknown

Community discussions

No discussions linked yet. Search DIY Solar Forum

Sources

  1. OutBack Power's own FLEXmax 100 AFCI Specifications datasheet, document 980-00078-01-001 REV C, dated October 2021, linked from OutBack Power's own outbackpower.com FLEXmax 100 AFCI product page. (OutBack Power · manufacturer · observed Sep 27, 2026)
  2. OutBack Power FLEXmax 100 Charge Controller FM100-300VDC-01 FM100-300VDC-AFCI Owner's Manual (900-0253-01-00 Rev C) (OutBack Power · manufacturer · 900-0253-01-00 Rev C · observed Oct 1, 2026)
  3. OutBack Power | FLEXmax 100A | MPPT Charge Controller (signaturesolar.com, October 4, 2026 capture) Paid link (Signature Solar · seller · observed Oct 4, 2026)
  4. OutBack Power | FLEXmax 100A | MPPT Charge Controller (signaturesolar.com, November 2, 2026 capture) Paid link (Signature Solar · seller · observed Nov 2, 2026)

Sign in to report an error on this page

Similar products

All with a price