Charged Reviews · Quick reference
LONGi Solar HIMO5 DC LR5-54HPB 410
- Brand
- LONGi Solar
- Model
- HIMO5 DC LR5-54HPB 410
- SKU / part number
- HIMO5 DC LR5-54HPB 410[1]
- Category
- Solar panels
Electrical at STC
| Rated output (STC) | 410 W[1, 3] |
|---|---|
| Module efficiency | 21 %[1, 3] |
| Voltage at max power (Vmp) | 31.42 V[1, 3] |
| Current at max power (Imp) | 13.05 A[1, 3] |
| Open-circuit voltage (Voc) | 37.4 V[1, 3] |
| Short-circuit current (Isc) | 13.84 A[1, 3] |
| Power tolerance | ? |
Temperature and system limits
| Temperature coefficient, Pmax | -0.34 %/°C[1, 3] |
|---|---|
| Temperature coefficient, Voc | ? |
| Temperature coefficient, Isc | ? |
| Maximum system voltage | 1,000 V[1, 3] |
| Maximum series fuse | ? |
| NOCT / NMOT | ? |
| Rated output at NMOT | ? |
| Operating temperature | ? |
Cells and construction
| Cell technology | Monocrystalline[1]Provisional |
|---|---|
| Cell count | ? |
| Bifacial | ? |
| Bifaciality | ? |
| Frame | Anodized aluminum alloy frame[3] |
| Front glass | Single glass, 3.2mm coated tempered glass[3] |
| Rear surface | ? |
| Panel format | ? |
Mechanical and connections
| Dimensions | 30 D × 1,134 W × 1,722 L mm[1, 3] |
|---|---|
| Weight | ? |
| Connectors | ? |
| Cable length | ? |
| Junction box rating | ? |
| Mounting | ? |
| Design load, front | ? |
| Design load, rear | ? |
Installation (from the manual)
Torque
| Clamp or bolt torque | 12 to 16 N·m(106.21 to 141.61 in-lb*)[4] |
|---|
Conductors
| Cable bending radius / connector notes | The minimum allowed bending radius of cables should be 43mm. (1.69 inch)[4] |
|---|
Clearances and orientation
| Mounting methods and clamp zones | Bolts Mounting, mounting rails cross the long frame: Outer Four-hole (Method ①) ±2400 Pa; Inner Four-hole (Method ②) +5400，-2400 Pa; Clamps Mounting, mounting rails cross the long frame (Method ③): 250≤D≤350 +5400，-2400 Pa; 350≤D≤450, 450≤D≤550 and 500≤D≤600 not given (/); Clamps Mounting, mounting rails cross the short frame, 150≤E≤250 (Method ④): ±2400 Pa; Clamps are mounted at the corners of short frame (Method ⑤): +2400，-1800 Pa[4] |
|---|
Grounding
| Grounding | There are grounding holes with the diameter of Ø4.2 mm at the edge location of module's back-side frame.; The copper core wire used for the grounding clamp is recommended to be 12 AWG.; Align grounding clamp to the frame mounting hole. Use grounding bolt to go through the grounding clamp and frame.; Put the tooth side of the washer on the other side and fasten the nuts.[4] |
|---|
Page 1 of 2 · Installation values · ? means nothing is recordedAggregated, often community-reported information, not official documentation. Do not rely on it for installation, purchase or compliance decisions; always confirm values with the manufacturer’s official documentation. Charged Reviews accepts no responsibility for errors.